Epson is among the most renowned printer brands in the world. They are renowned for their impeccable print quality and high-end performance. But, Epson printers, just like other equipment, could experience a certain amount of wear and tear at times. Each driver or printer comes with many flaws. Sometimes, the issues arise because of mechanical or technical causes that could at some point be beyond our control. Similar to a common issue that users encounter when they use Epson printers. It is Epson Printer error code 0x97.
The purpose of this article is that we’ll look into and solve the problem with the error code 0x97 for Epson printers.
What is What Do You Mean by Epson Error Code WF-3640 What is 0x97?
This Epson WF-3640 printer error code, 0x97 can be seen by those who utilize their printers for a long period. There isn’t any specific indication or warning that you might receive in this kind of error. Instead, the error appears. The errors must be corrected immediately or you’ll not be able to make use of your printer. They typically disrupt the operation of the printer and cause the printer to shut off and off.
This Epson error message 0x97 could be observed on the display’s LCD. The error occurs when you’re working on a print job, causing your printer to stop abruptly. It is most often seen in Epson WorkForce Series.
Solutions to Fix Epson Printer Error Code 0x97
Remove All Printers from Printer
The first step you should do is remove every printer device. You must stop all printing jobs and eliminate all jammed paper from your printer. The word “disconnect” is not the same as disconnecting from the internet. You must unplug all cords, wires cables, etc. of your printing device. Make sure to remove your cartridges of ink too. This procedure is fairly simple and could be effective, based on the reason for the issue.
For one minute, keep pressing and pressing the printer’s Power button. You must now reconnect everything you disconnected previously. All cables, wires, USB. Installing the cartridges for ink. Press the Power button, switch on your printer, then run the test print. Examine if there have been any modifications to the error. If you find that the error code is 0x97 and not solved, move on to the next step.
Reset your Printer
If disconnecting/reconnecting your printer did not solve your problem then this might help. It is necessary to disconnect all the printer’s cables. The printer should rest for approximately five minutes before starting. Then, press and hold your power button for about a minute. Keep pressing and holding the Power button as you connect each wire back.
Press and hold the power button again for about a minute, then release the button. Print a test to determine what improvements can be made. If the issue persists, move on to the final solution.
Clean the Print Head
Sometimes it is possible that the Epson error code 0x97 can be due to the printhead being dirty and blocked. If that is the case, the remedy is to clean the printhead in a proper manner. Here are the steps needed to clean the Epson printer’s printhead
- Get each ink cartridge from the printhead separately. Place the cartridge in a fresh towel or piece of paper. After that, gently remove your printer’s printhead.
- Clean the printing head’s bottom with a clean, lint-free damp cloth. Continue to wash the nozzle until there is no black ink adhering to the surface.
- Place the printhead in warm water for about 10 minutes. Avoid boiling water. Use a clean towel in the bottom of the bowl and allow the printhead to rest over it while it soaks. Take the printhead out of the bowl, then take care to gently remove any moisture and water using a dry cotton cloth.
- Place the printhead on the top of a paper towel and let it air dry itself for about 15 mins. After that, you can put the printhead back in the carriage and install each cartridge into its respective position. Connect your printer to the internet and see if the issue is resolved.
Install and upgrade your security against malware
Sometimes this error could be due to malware. In the event that Epson Error Code 0x97 occurs caused by malware, you must upgrade or install your printer’s malware security.
This is an Epson Printer error code is 0x97. This is a common hardware error that signifies that your printer is totally unusable. You will not be able to use the printer if you don’t repair the issue. The solutions mentioned above may aid you but if your issue persists, you may require assistance from a professional. You can connect to us through our Printer customer support number.
Also Read: 8 Tips to Tackle with Brother Printer Offline Issue
